TD1410 PDF

Techcode TD datasheet, 2A KHZ 20V PWM Buck DC/DC Converter (1- page), TD datasheet, TD pdf, TD datasheet pdf, TD pinouts. Find great deals for 5pcs Power PWM Controller TD Sop8. Shop with confidence on eBay!. Altech TD Terminals are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for Altech TD Terminals.

Author: Mogami Nazilkree
Country: Andorra
Language: English (Spanish)
Genre: Sex
Published (Last): 15 August 2004
Pages: 327
PDF File Size: 3.43 Mb
ePub File Size: 3.26 Mb
ISBN: 200-7-48045-658-8
Downloads: 45580
Price: Free* [*Free Regsitration Required]
Uploader: Nizahn

The data for these curves was taken with the TD SOP8 package operating as a buck-switching regulator in an tx1410 temperature of 25oC still air. These temperature rise numbers are all approximate and there are many factors that can affect these temperatures. Bypass Vin to GND with a suitably large capacitorto eliminate noise on the input.

FB Senses the regulated output voltage to complete the feedback loop. Exposure to absolute maximum rating conditions for extended tx1410 may affect reliability. The effectiveness of the PC board to dissipate heat also depends on the size, quantity and spacing of other components on the board, as well as whether the surrounding air is still or moving.

Typical Application Circuit 3. Other factors are, trace width, total printed circuit copper area, copper thickness, single or double-sided, multi-layer board and the amount of solder on the board.

Datasheet 2A KHZ 20V PWM Buck DC/DC

A suitable input bypass capacitor must be present at this pin to minimize voltage transients and to supply the switching currents needed by tx1410 regulator GND Circuit ground. Parameters Symbol Test Condition Min. The TD serves as ideal power supply units for portable devices. As in any switching regulator, layout is very important.

The output ripple voltage is due mainly to the inductor sawtooth ripple current multiplied by the ESR of the output capacitor. To minimize coupling to sensitive circuitry, the PC board copper area connected to this pin should be kept a minimum.

Furthermore, some of these components such as the catch diode will add heat to the PC board and the heat can vary as the input voltage changes.

Dt1410 open core inductors are used, special care must be taken as to the location and positioning of this type of inductor. Large areas of copper provide the best transfer of heat lower thermal resistance to the surrounding air, and moving air lowers the thermal resistance even further.

5pcs Power PWM Controller TD Sop8 | eBay

TD operates from a 3. This pin should be placed outside of the Schottky Diode to output capacitor ground path to prevent switching current spikes from inducing voltage noise into TD For the best thermal performance, wide copper traces and generous amounts of printed circuit board copper should be used in the board layout. Drive EN pin high to turn on the regulator, drive it low to turn it off. An enable tr1410, an over current protection function and a short circuit protection function are built inside.

Supply Voltage Input Pin. The SOP8 package needs a heat sink under most conditions. Package thermal resistance and junction temperature td141 numbers are all approximate, and there are many factors that will affect these numbers.

This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation is not implied. Once exception to this is the output switch pin, which should not have large areas of copper. Stresses greater than those listed under Maximum Ratings may cause tc1410 damage to the device. The size of the heat sink depends on the input voltage, the output voltage, the load current and the ambient temperature.

Allows the switching regulator circuit to be shutdown using hd1410 level signals thus dropping the total input supply current to approximately 30uA. T1410 using the adjustable version, special care must be taken as to the location of the feedback resistors and the associated wiring.

TD1410-1.8A 380KHZ 20V PWM Buck DC/DC Converter

For the inductor, depending on the physical size, type of core material and the DC resistance, it could either act as a heat sink taking heat away from the board, or it could add heat to gd1410 board. An internal compensation block is built in to minimize external component count. The TD junction temperature rises above ambient temperature for a 2A load and different input and output voltages.

A suitable input bypass capacitor must be present at this pin to minimize voltage transients and to supply the switching currents needed by the regulator. Vendor Web Site 1 Diodes,Inc.

Some of these factors include board size, shape, thickness, position, location, and even board temperature. EN is a digital input that turns the regulator on or off. The voltage spikes are present because of the fast switching action of the output switch, and the parasitic inductance of the output filter capacitor, To minimize these voltage spikes, special low inductance capacitors can be used, and their lead lengths must be kept short.

Icc vs Temperature Figure 8. The device includes a voltage reference, oscillation circuit, error amplifier, internal PMOS and etc. The feedback threshold voltage is 1. Through an external resistor divider network, FB senses the output voltage and regulates it.